QRZ! Ham Radio 5

home *** CD-ROM | disk | FTP | other *** search

/ QRZ! Ham Radio 5 / QRZ Ham Radio Callsign Database - Volume 5.iso / files / arrl / faq / faqrtty.txt < prev next >

Wrap

Text File | 1994-11-27 | 34.0 KB | 882 lines

Shareware RTTY/FAX Decoding Programs for the IBM PC Frequently Asked Questions by Dave Moisan, N1KGH Last Revised--30 April 1993 Many people have gotten interested in receiving RTTY and FAX transmissions with their PC's. Shareware, combined with cheap, easy- to-build hardware, has put RTTY and FAX reception in reach of anyone with a good digital portable such as the Radio Shack DX440 or Sony 2010. Two programs have become very popular: Hamcom 2.1, a RTTY terminal program, and JVFAX 5.1, a full-featured FAX/SSTV receive program. The two programs both use an identical basic interface, so one can get started in FAX and RTTY for almost nothing. Another program, PKTMON, lets you monitor HF and VHF packet off the air, using the same hardware. This FAQ list is divided into five sections: Introduction Using HamComm Using JVFAX Using PKTMON General Problems Appendix--HamComm Interface Schematic and Parts List INTRODUCTION ------------ ** Where do I get the software? HamComm and JVFAX are available from a number of sources on the Internet, including simtel20.army.mil and nic.funet.fi (/pub/ham/misc); look for HAMCOM21.ZIP and JVFAX51.ZIP. PKTMON 1.2 is available from nic.funet.fi and should be on Simtel as I post this. ** What are the basic system requirements? HamComm: XT or better, 320K RAM, hard disk not required. JVFAX: 286 or better, at least 1M RAM; a hard disk is strongly recommended. Note that JVFAX has its own extended memory driver, which may conflict with HIMEM.SYS and other memory drivers. Pktmon: 286 or better. ** What are the basic receiver requirements? I've successfully received RTTY, fax and Packet with my Radio Shack DX400 digital portable, and have had less luck with CW. Receivers like that will work, but table top radios (Kenwood, Icom and Yaesu) and ham transceivers are much more suited for this application. ** Where can I find plans for the basic interface? The plans are included in the documentation for both Hamcom and JVFAX. JVFAX has schematics for both the basic interface, and a more sophisticated interface that also receives GOES/APT satellite pictures. A complete schematic and parts list is included at the end of this FAQ list. ** I don't want to build it. Can I buy a interface? Yes. William Nolle is selling his version of the interface, called FAXCAP, and it includes all software discussed here. Contact him at: William Nolle 122 Phillips Rd Hazel Green, AL 35750 (Disclaimer: I am not affliated with William, nor am I even a customer, but merely a friend and fellow enthusiast.) Also, Dieter Dippel is selling an interface (with surface- mount components) which includes JVFAX and HamComm. Contact: Dieter Dippel Fenitzer Str. 33 D-8500 Nuernberg Germany ** How does the interface work? This is a zero-crossing detection circuit, made up of a 741 connected in an open-loop configuration. For every zero- crossing (twice a cycle), an interrupt is generated. HamComm measures the time between successive interrupts using the PC timer chip. ** How do I connect it to my radio? Simply run an audio cable from the interface box to the earphone/ headset output, record output, or data output of your radio. The Sangean 803A has a record output, and the DX440 can be modified for same. Note that the interface needs 100 mV of audio to work, but most rigs can easily supply this. ** Can you transmit with the interface? Depends on the software, and how you construct the interface. Hamcomm will send through the speaker or TxD line of the serial port; JVFAX sends through the speaker. Pktmon doesn't transmit at all. See the appendix for details. USING HAMCOMM ------------- ** How do I set up HamComm? There's a sample configuration file in the HamComm archive, HC.CFG which explains the numerous parameters required for the program to run. Here are the ones you should set: select port com<n> (Select default com port, <n=1 to 4>) Note: COM1 and COM2 are already defined. If you need to use COM3 or COM4, here are the "define port" statements to use: define port com3 iobase 0x3e8 irq 4 define port com4 iobase 0x2e8 irq 3 You don't need to do this for COM1 or COM2 unless you have an unusal setup. ** Where can I find RTTY on HF and what does it sound like? The ham bands are the best place to find decodable RTTY. I tune into CFH, Halifax, Nova Scotia on 4271, 6496.5 and 10536 KHz. RTTY is usually sent on the half-hour. RTTY has a "deedle- deedle" sound that you're probably familiar with if you've ever randomly tuned shortwave. If you want to know what an RTTY signal sounds like, go to the RTTY screen (F3) and try control-T (transmit on/off). Type in some text and hit ENTER. You will hear a signal from the PC speaker according to the currently selected speed, shift and center frequency. ** How do I tune RTTY? First, hit F9 for the tuning screen and, using the arrow keys, set the center frequency to 1200 Hz. For example, if you're trying to decode the ARRL bulletins on 3625 KHz, the tuning screen should look like this: Signal Frequency: 01### Hz 0 . . . .500 . . . .1000 . . . .1500 . . . .2000 . . . .2500 Hz Space -> | | <- Mark | Center Frequency: 01200 Hz Using the arrow keys, move the lower tuning bar between the two upper tuning bars. You may need to vary your BFO, RIT or clarifier so that the upper bars are centered on the display. The difference between the two frequencies, or "distance" between the two upper bars is the *shift* of the RTTY signal. Hit Alt-K and select the appropriate shift--in this example, 170 Hz. You'll know when the signal's tuned properly, because a train of square waves will appear at the bottom of the screen. Next, hit Alt-S and select the *speed*; Ham RTTY is usually 45 baud. Outside of the ham bands, 50 and 75 bauds are most common (Note: If you're mathematically adept, you can figure out the speed yourself. Hit F8 to select the Scope and freeze the display by hitting Return. Measure the time interval of the _shortest_ peak, and calculate Baud rate = 1/t*10**-3, where t is in milliseconds.) Now, hit F3 (for Baudot), and readable text should scroll forth on the screen. If it doesn't, hit the Tab key to toggle between Normal and Inverted keying. If text is still unreadable, hit Alt-S and adjust the speed. ** How do I log RTTY to a file? Hit Alt-F R or Alt-F W; select the directory or file you want to save to and hit Return. To stop logging, hit Alt-F R. Here's some RTTY recorded off the air on 4271 Khz (at 0230 UTC): avalon peninsula east coast the bonavista peninsula only. freezing rain warning continued for the bonavista peninsula only. tonight..overcast. intermittent drizzle or freezing drizzle. periods of freezing rainpm yrkwivonavista peninsula ending overnight. winds becoming strong northerly. low zero. friday..cloudy. patchy freezing g7+)-01vtov ** Whenever HamComm is receiving a string of numbers (like from CFH or other weather stations), it comes in garbled. HamComm has a AutoLetter mode that automatically shifts from Figures to Letters after 5 characters have been received. Turn this off with Control-L; the "L" at the bottom right of the display should disappear. This feature is akin to the "Unshift On Space" option found on other decoders. ** I found RTTY, but Hamcom can't decode it. A sad fact of life in the shortwave bands is that at least 3/4's of all RTTY is encrypted, and alas, much of the unencrypted traffic is not sent in plain Baudot. There still are many decodable signals, but you'll need good references to find them. ** How do I decode CW? Decoding CW is similar to decoding RTTY, except that there's only one frequency to be concerned with. While you hear the CW, go to the decoding screen, as below: Signal Frequency: 01200 Hz 0 . . . .500 . . . .1000 . . . .1500 . . . .2000 . . . .2500 Hz | | Center Frequency: 01200 Hz Just move the arrows so that the lower line is lined up with the upper and hit F2. Here's a sample of CW copied off the air, on 4281 Khz vvv vvv vvv cqde vcs vcs vys qsx 4 6 and 8 mhz chnl 3/4/7/8 vvv vvv vxv cq de vcs vcs vcs qsx 4 6 and 8 mhz chnl 3/4/7/8 vvv vvv vvv cq de vcs vcs vcs qsx 4 6 and 8 mh7 chnl 3/4/7/-.--.. vvv vvv vvv cq de vcs vc5 vcs qsx ......- 6 und 8 mhz chnl 3/4/7/8 Note that HamComm subsitutes dot-dash marks for any character it can't decode. ** I'm hearing CW, but Hamcom just garbles it. There are two different problems encountered with CW decoding in HamComm. Here's what Django, DL5YEC, author of HamComm has to say: Problem 1: Tone detection For many people it is obvious that an RTTY signal has two states, usually called mark/space or high/low tone. ANY data transmission requires at least two states for 1 bit at a time and CW is no exception. So what are the two states for CW? They are the tone and ... NOISE ! You may be surprised to hear that a certain amount of noise is REQUIRED to detect that the tone has ended. HamComm has an indicator for the tone detector output. At the bottom of the RX window, just to the right of the WPM display, is a small white dot that jumps up and down: up = tone detected, down = no tone (noise) detected. Listen to the signal and watch the jumping dot. It should follow the signal precisely and not jump around nervously or stick to one position. The input signal is compared to the currently selected mark/space tones. To be regarded a valid tone the signal has to stay in that range for a certain amount of time. So the behaviour of the detector mainly depends on the currently selected SHIFT. The tone detector output as displayed by the dot is the input to the character decoder. Problem 2: Character decoding In theory a dash is three times as long as a dot, the gaps within a character are dot-sized and the gaps between characters are dash-sized. In reality there are short and long tones and gaps of variable size because CW is usually 'hand-made.' The speed and length ratios also change during a transmission if the operator gets tired. HamComm keeps a floating average of the tone duration to adjust to speed changes. Overall decoding quality mainly depends on the tone detector. As an aside, I should mention that the bouncing-dot display also works great for RTTY; just tune the receiver until the dots bounce equally between top and bottom. USING JVFAX ----------- ** How do I set up JVFAX? Select "Configuration" from the menu, and you should see a Config screen. Options are set using the arrow keys to select, and the space bar, - or + to set each option. Here are the options you need to set: Demodulator: Set to "7 bits" and "Comparator/IRQ 4" or "Comparator/IRQ 3". Specify the address according to the following table: For: Specify IRQ: and Address: ---- --- ------- COM1 4 03F8 COM2 3 02F8 COM3 4 03E8 COM4 3 02E8 Graphics and SSTV-Graph: Set this as appropriate for your system. Most users can specify "VGA (640x480)". A number of Super VGA cards are supported, but you'll have to refer to your VGA manual for register settings. Printer: Again, set this as appropriate for your system. Most popular dot matrix printers and the HP Laserjet are supported. (As an example, for my Panasonic 1124, I selected "Epson 24-pin".) Enable scrolling: This determines whether faxes will scroll off the screen when being received. Set this to "Yes". Default Picture Directory: Enter the disk and directory where faxes will be stored, e.g. "C:\WEFAX". Store Pictures in GIF 89a: JVFAX uses the GIF 89a standard to store special information on each fax, such as mode, LPM and IOC. Unless you're using other GIF software that can't handle this standard, leave this enabled ("Yes"). Miscellaneous Settings: Hit Esc to enter yet another configuration menu! There are just two settings you need to make: Quicksave: This feature lets you save the last picture sent; it works by continuously capturing faxes to a .GIF file, which may become *very* large. Unless you have lots of hard disk space, set this "off". Initial RX Mode: Set to "1--Wefax 576"; this is the mode that almost all weather faxes are sent in. Hit Ctrl-Enter to leave this menu. Hit Ctrl-Enter again, and you're done! ** Where do I find fax and what does it sound like? A Fax signal will have a "scratchy wheel" sound when sending a picture, and a carrier tone when idle. It can be found easily in the maritime bands. Unlike RTTY, there are few variations, and no transmissions are encrypted that I know of. Two stations I hear regularly on the US East Coast are NAM, Norfolk, VA on 3356, 8080 (irregular) and 10865 KHz, and CFH, Halifax, NS on 4271, 6496.5 and 10536. CFH sends faxes on the hour, generally. I've found press fax on 9244, from Buenos Aires, Argentina. ** What modes are faxes usually sent in? Weather faxes are usually sent with an IOC (Index of Correlation-- the ratio of width to height) of 576, and an LPM (Lines Per Minute) of 120. Press faxes, the few I have found, use an IOC of 288 and an LPM of 60. ** OK, I'm hearing it. How do I tune in? Using NAM, 10865 KHz as an example, follow these steps: 1) From the JVFAX main menu, hit F (Fax), and you'll be shown a blank screen with a tuning indicator and a menu box on the bottom of the screen. 2) Select the mode by hitting 1 ("Wefax 576"). 3) Set the deviation to 400 by hitting the D key till it comes up. 4) Using your BFO, RIT or clarifier, tune the signal (in lower sideband) until you see a peak on the tuning indicator. Tune this peak towards the W (white) end of the scale (This will normally be 1.9 Khz below the center frequency, in this case 10863.1 Khz.) The indicator should look like this: ! <- Signal ! peak ! should . . . .. .. .. . . ##! be here ----------------------------------------- B W 5) Hit A (APT); it should read "Running" and you should start to see a fax appear on the screen! To stop recieving, hit A again. ** I don't get a fax, or I get something garbled. Check the mode; most fax transmissions use "Wefax 576", mode 1 in the program. The LPM should be 120. Check your connections to the interface. If that's in order, you may have an RFI or interrupt problem (see questions in "General Problems"). ** I get a fax, but it comes out slanted. Hit / and a line will appear; use the arrow keys to tilt and move the line so that it's lined up with a line on the fax (such as a border or a chart line). Hit Return, and the fax should now come in straight. Note that this is a permanent adjustment, and you shouldn't need to fix this ever again, no matter what faxes you subsequently receive. ** I get a fax, but it's not aligned with the edge of the screen. Hit R (Rotate) and move a line with the arrow keys to the left edge of the fax (there'll be a black bar where the fax is supposed to start.) Hit Return and the fax should now be properly aligned. ** My fax is negative! You're receiving the fax on the wrong sideband; try the other sideband. Most faxes will be sent in LSB. A few press stations transmit negative pictures (JVFAX can be set to fix this; see the docs.) ** My fax is too dark. My fax is too light. Your receiver is mistuned. If the fax is too dark, tune towards the white end of the tuning scale (peak moves towards W). If the fax is too light (washed out), tune towards the black end of the tuning scale (peak moves towards B). Also, make sure the deviation is set correctly, at 400 for most faxes. This is especially important for receiving the GOES satellite images that NAM sends. ** How do I save a fax to disk? While you're not receiving a fax (APT "waiting"), the S key will toggle the save-file option on and off. Faxes will be saved in .GIF format to the disk and subdirectory you specified in the configuration screen. ** How do I print a fax? Two ways: 1) While you're in the fax receive mode and not receiving a fax (APT "waiting"), P will enable your printer; it's a toggle, so hit P again to disable printing. NOTE: You cannot have both Save to File and Print options enabled at once. Also, once the fax is printing, the Rotate command will not work on the printout. 2) Hit H (Show and Send Pictures). Select the fax you want to print. When it appears on the screen, hit P. JVFAX will ask how much width it will print in (0-100%); hit Return for the default (100%). ** The GIFs I save are too big! How do I shrink them? It's not uncommon for weather faxes to be very large, especially if you regularly pick up 16-shade GOES images over NAM (a recent GOES fax from them "weighed in" at 870k!) There are several methods you can use to shrink the size of your GIFs: 1) You can crop them. From the main menu select H (Show and Send Pictures); from the directory listing, select the file you want to crop. The fax will show up on the screen--select the Z (Zoom) option. Use the arrow keys to move the zoom box (which is about the size of a regular 640x480 VGA screen), and the X, Y, + and - keys to resize it. Hit Return and the cropped image will fill the screen. Hit S to save it (under a different name.) 2) You can reduce the resolution on faxes to be received. Most faxes (of the Wefax 576 variety) have a resolution of 1810x 1000, which makes for beautiful printouts, but is overkill if you're just using a GIF viewer. To fix this, go into the Mode Editor (M from the main menu) and select the mode you normally use (e.g. Wefax 576). Step through the options with the arrow keys and select Resolution. For Wefax 576, it'll normally be 1810. Enter a smaller value (800 is OK) and hit Return. If you're only interested in charts and not satellite images, select the Grays option and set the number of shades to 2 (B&W only--no gray scale). Your GIFs should be much smaller, though at a significant loss of resolution. (That being said, I once saved some GOES images from NAM for a friend of mine in 800x600x4 and they still looked good.) ** I get an all-white/all-black signal, no matter what signal is coming in on the receiver. Either your audio cable to the interface is broken, or you have an interrupt conflict between serial ports. If it's the latter you may need to move the interface to another port. Note that MSDOS's HIMEM.SYS may conflict with JVFAX. (At least it does on my setup [286, 1M, DOS 5.0]) (See "General Problems" for more on this.) USING PKTMON ------------ Unlike HamComm and JVFAX, Pktmon has few options and is simpler in scope. Using the same interface, Pktmon will decode HF and VHF packet. Pktmon can log to a file, and will optionally keep track of packets, assembling them into separate files for you. Note that the program is receive-only. While it will never approach, let alone replace, Baycom or a TNC, I've been delighted with its very ingenious attempt at implementing AX.25 in software, and have found it a surprisingly fair performer. It even comes with source code (Turbo Pascal) for implementing your own projects with the interface! There isn't much to running Pktmon, so here's a quick rundown through the prompts. "COM 1 or 2?" Self-explanatory. Pktmon doesn't support COM3 or COM4. "Packet type?" Enter 1 for HF packet or 2 or 3 for VHF packet. I've never noticed a difference between the latter two options in use. "Log bad packets?" If you answer Y, packets with CRC errors will printed, otherwise, not. I usually choose to log them. "File to log all packets" Self-explanatory. If you don't specify a file, packets will go on the screen. "File to log sorted packets" Enter a filename, _no extension_. Pktmon will sort packets to the files <n:filename.#>, #= 0 to 9. It also creates a file <n:filename.OTH> for uncategorized packets such as beacons. That's it. Pktmon will start decoding packets until you hit Return. There's a tuning indicator on the top of the screen that indicates activity. Here are some sample unsorted packets copied off the air on 14099 Khz around 2300: Started Logging on 1993-04-16 at 18:00:11 [...] 18:03:00 => CQ -0 WA2GGI-0 Ctrl:03 [UnAck Info] Pid:F0 Data: #0D 18:03:11 => K4YPE -0 WA2GGI-0R Ctrl:73 18:03:13 => K4YPE -0R WA2GGI-0 Ctrl:00 [Data, seq 0] Pid:F0 Data: **HI BOB IN BOCA RATON FL.BUSY NOW PLEASE LEAVE MESSAGE ON MAILBOX TNX.#0D 18:03:23 => K4YPE -0R WA2GGI-0 Ctrl:04 [Data, seq 2] Pid:F0 Data: ,RM,S, or Help >#0D 18:03:35 => K4YPE -0 WA2GGI-0R Ctrl:73 18:03:38 => KB7HJM-0 WA2GGI-0 Ctrl:63 18:03:41 => KB7HJM-0 WA2GGI-0 Ctrl:00 [Data, seq 0] Pid:F0 Data: **HI BOB IN BOCA RATON FL.BUSY NOW PLEASE LEAVE MESSAGE ON MAILBOX TNX.#0D [...] 82 total frames received and 6 good ones + 3 CRC errors Stopped logging on 1993-04-16 at 18:20:42 It's rather like reading the news on an RS232 service monitor, isn't it? :) Note that control characters are depicted as "#cc". Now, here are some sorted packets: ****** File open at 18:03:16 on 1993-04-16 for WA2GGI-0 => K4YPE -0 traffic **HI BOB IN BOCA RATON FL.BUSY NOW PLEASE LEAVE MESSAGE ON MAILBOX TNX. [1 lost pkts] ,RM,S, or Help > ****** connection inactive for 5 minutes ****** File closed at 18:09:02 on 1993-04-16 ****** File open at 18:13:28 on 1993-04-16 for KC4FS -0 => W1DXQ -0 traffic Phone call Jack. Please wait... ****** connection inactive for 5 minutes Now, the questions: ** Where do I find packet and what does it sound like? On HF, packet can be found mainly at the lower end of 20 meters (14090-14150 usually) and in the 30 meter band (10100-10150 Khz). VHF packet can be found on 145.01, 145.03, 145.05, 145.07 and 145.09, among other places. It has a "braaaap..." sound quite unlike RTTY. ** How do you tune in packets on HF? On the upper edge of the screen, there's an "A" scale. While hearing packets, tune VERY carefully until the scale reads 6 or higher. Pktmon expects a tone frequency of about 1000 Hz. ** I'm logging sorted packets, but they're missing linefeeds. You'll have to go into your favorite ASCII word processor and have it insert linefeeds. I usually copy all the <n:filename.#> files into a single file and fix it there. ** I'm getting lots of CRC errors. On HF, this is, sadly, normal. Packet is just not well suited to a ever-changing ionosphere, and it's marvelous that it works at all. (When I copied the sample text, the ionosphere was *very* quiet, an unusual occurence as I'm writing this.) On VHF, on the other hand, CRC errors may be a result of Pktmon being unable to keep up with transmission. 1200 baud is near the limit for this type of interface. I've also found that with my setup (in an apartment), I seem to be prone to multipath and other VHF anomalies that disrupt reception, especially of packet. ** The program locks up on me when receiving lots of packets! If there's too much activity on the air, or the receiving tone frequency is too high, Pktmon tends to lock up, as it can't "follow" the signals fast enough. This has been reported by several users on Fidonet. According to the author, Pawel Jalocha, if Pktmon takes a long time to terminate upon hitting Return, your machine may be too slow. GENERAL PROBLEMS ---------------- ** Can I use EMM386/QEMM or other memory managers with HC, JVFAX or PKTMON? Generally, no. HamComm, JVFAX and PKTMON are interrupt-intensive and use up most of the CPU cycles. That's the price you pay for having the demodulation and decoding done in software (rather than in a TNC). JVFAX comes with its own memory manager, anyway. Note: JVFAX may not work with MSDOS's HIMEM.SYS. You may need to remove the "DEVICE=HIMEM.SYS" and "DOS=HIGH" statements from your CONFIG.SYS before using JVFAX. I've not seen any problems with HIMEM and HamComm or Pktmon. If you regularly use EMM drivers, Windows or Desqview, make up a minimal boot disk disabling all such programs, before running HamComm, JVFAX or PKTMON. ** I get noise from my computer--HELP! One of the most difficult problems in linking the PC with the radio is RFI. It's beyond the scope of this FAQ list to cover every possible contingency, but here are some suggestions: 1) Keep your computer and your antenna *well* separated from each other and use good, well-shielded, coax for the lead- in. 2) The HamComm interface should be *shielded*--use a metal or foil-lined box. Use good shielded cable for both the audio and data connections. 3) Use RFI toroids (available at Radio Shack) on all cables. 4) Install 0.1 uF capacitors from the DTR and RTS lines to ground. 5) Install an audio isolation transformer between HamComm and the radio. (Radio Shack #273-1374). 6) Make sure the monitor, printer and their connecting cables are well shielded. Monitor noise is very common, as is printer noise. In my case, I had to do all of those steps. My 286 PC was feeding RFI back through the earphone jack of my radio), *desensing* it (ouch!) I never got all the RFI out, but I reduced it considerably so that I only get a slight increase in background noise on a few frequencies. APPENDIX -- THE HAMCOMM INTERFACE SCHEMATIC ------------------------------------------- Here's a schematic of the HamComm interface, reproduced with permission: HamComm 2.0 Receive Circuit Copyright (c) 1990, 1991 by W.F. Schroeder RS232 25pin 9pin D1 -------*--------*-I<--*--> DTR 20 4 | | | D2 | 3 |\ | | ---->I--- >------| |--*-----|+ \ 7 | | | C1 | | \____|______|_|________> DSR 6 6 .1 uF| 2 |741 /6 | | | D3 | ---|- / | | --I<-- AF | | |/ |4 | | D4 | In | | ---*---|------*--->I--*--> RTS 4 7 R1, R2 [ ][ ] | | + | 100K | | === === C2, C3 | | | === === 1 uF | | | + | | 16V | >-----------*--*--------*---*--------------|---> GND 7 5 | | PTT Circuit E | | (omit for receive-only) ^\ R3 | D1-D5 Q1 \I 1K D5 | 1N914/4148 2N2222 I----[ ]----I<--| PTT /I B <-----------------------/ C Transmit Audio Circuit R2 R3 (omit for receive-only) 15K 15K --------*----[ ]---*----[ ]----*----< Out C1 | | | R4 | .1 uF [] R1 | | 220K| <----| |--->[] 10K === C2 === C3 [ ] PC Speaker MIC [] var. === .022 === .022 | Out | | uf | uF | <------------*-------*----------*-----------*----< +5V NOTE: HamComm sends RTTY through the COM port's TxD line, as well as the speaker. See the HamComm docs for more details. If you're just interested in receive, omit the PTT and transmit audio circuitry. None of the parts are critical, so raid your junkbox! Prices for equivalent Radio Shack parts are given for reference--which you can beat by judicious shopping/scrounging. Parts List -- Main Circuit -------------------------- Part Value Radio Shack # Price (1993) C1 0.1 uF 272-135 $0.59 (for 2) C2, C3 1 uF 16 V 272-1434 $0.59 each D1-D4 Diode, 1N914 276-1122 $0.99 (for 10) *D5 Diode, 1N914 276-1122 IC1 Op amp, 741 276-007 $0.79 R1, R2 100K 271-045 $0.29 (for 2) *R3 1K 271-023 $0.29 *Q1 Trans. 2N2222 276-2009 $0.59 * Not needed for receive-only interface Parts List -- Transmit Audio Filter ----------------------------------- Part Value Radio Shack # C1 .1 uF 272-135 $0.59 (for 2) C2 .022uF 272-1066 $0.69 (for 2) C3 .022uF 272-1066 R1 10 K var. 271-282 $0.49 R2, R3 15 K 271-036 $0.29 (for 2) R4 220 K 271-043 $0.29 Miscellaneous: Enclosure (RS #270-239 recommended, $2.19), PC board (RS #276-170, $2.79), audio jack (RS #274-316, $2.19 for 4), RFI toroids (RS #273-104 $7.95 for 2), DB-9 connector (RS #276-1536, $1.29), audio cable, plug to match radio. If you buy all Radio Shack parts for the converter, it should cost $15 for the full circuit (plus transmit portion), not including the RFI toroids. Again, the circuit is not really critical--if you have any parts lying around that fit, use them! CLOSING COMMENTS ---------------- This FAQ list was the inspiration of myself and many others on the Fidonet SHORTWAVE echo, who have been using and experimenting with HamComm and JVFAX for over six months, trading ideas and hints along the way. When more people asked me for help, there and on the Internet, I thought of the obvious and wrote this! <g> The following get credit for lending me a hand: W.F. Schroeder (DL5YEC), Pawel Jalocha (SP9VRC), Reid Kelly, John Palaima (N1NIG), William Nolle, Tom Carney (WB9RJX), Ken McKenzie, Derek Buchler and Stephen Lee. Additions wanted ---------------- 1) I'd like a list of "cornerstone" RTTY and FAX frequencies. In other words, if you're on the US West Coast, in Europe, Africa, the Mideast or Asia, what stations do *you* hear best? I'm not looking for an entire Klingenfuss text, just a few good frequencies for various parts of the world. 2) I've learned of another fax program, HFFAX5 (no, it's NOT related to SSC's software as far as I can tell..) The doc files that come with it are of the "I got this neat program from a friend-of-a-friend" slant, and I'd like to find out its status (shareware, freeware or pirateware) before I write about it further. Nothing gets my goat like mysterious ZIP files with no documentation! 2A) And has anyone used FFTMORSE (Soundblaster CW) or TOR117 (AMTOR terminal unit in software)? 3) I'd like to hear from anyone who's tinkering with the interface or even the Pktmon source. 4) I do intend to update this list with the introduction of new shareware, updates to existing programs, or (most likely) stuff everyone else is using but that I never heard of. <g> (A new version of HamComm is slated for later this year, BTW.) More questions? --------------- If anyone has questions or comments or even flames, drop me a line! My address(es): Internet: moisan@silver.lcs.mit.edu n1kgh@amsat.org Snailmail: David Moisan 86 Essex #204 Salem, MA 01970 73's and Good Listening, Dave | David Moisan, N1KGH /^\_/^\ moisan@silver.lcs.mit.edu | | 86 Essex St. Apt #204 ( o ^ o ) n1kgh@amsat.org | | Salem. MA 01970-5225 | | | \-----------------------------------------------------------------/